Climatronic Koder - med instruktionsvideo :)

[ThomasMN]

Jeg tager intet ansvar for dette overhovedet. Evt. google Climatronic Codes

The speedometer has a factory built-in error to show a speed faster than your actual speed. The Climatronic (automatic climate control) system includes a number of sensors that you can access through the diagnostic mode. To see your true speed in digital format press the following key combinations:
1. Press Fan Down, Temperature Colder, ECON at the same time.
2. Use the temperature control buttons to cycle through the various channels to Channel 16.
3. Press ECON to go back to normal. (It goes back automatically when you restart the car.)

Channel Information Type Component VAG-COM Block
0 Adjustable
1 Temp climatronic instrument panel (-G56-) Sensor (meas block val 7.3)
2 Sensor or Value Learned
3 Sunlight photo sensor (located on dashboard) - values from 0 - 120% Sensor (meas block val 6.4)
4 Outside air temp - -E87- Calculated from -G89- and -G17- (?) Value Learned (meas block val 6.1)
5 Outside air temp - -G17- lower bumper sensor (?) Sensor (meas block val 6.3)
6 Outside air temp - -G89- air intake duct sensor (from engine?) Sensor (meas block val 6.2)
7 Outlet temp Floor sensor (-G192-) Sensor (meas block val 7.2)
8 Outlet temp Center sensor (-G191-) Sensor (meas block val 7.1)
9 Blower speed Adjustable
10 Measured blower speed Sensor
11 Temperature regulation 0 = Hot, 255 = Cold Adjustable Temperature reg flap motor -V68-
12 Dashboard ventilation valve Adjustable Central air flap motor -V70-
13 Recirculation valve Adjustable
14 Lower ventilation valve Adjustable
15 Sensor or Value Learned
16 Car speed Sensor
17 Sensor or Value Learned
18 Sensor or Value Learned
19 Sensor or Value Learned
20 Sensor or Value Learned
21 Sensor or Value Learned
22 Sensor or Value Learned
23 Coolant temp in HVAC heater element (?) Sensor
24 Temp wanted in heater or car (?) Adjustable
25 Position heated air Value Learned Temperature regulator flap motor -V68- (meas block val 2.4)
26 Actual value Sensor Temperature regulator flap motor -V68- (meas block val 2.1)
27 Position cooled air Value Learned Temperature regulator flap motor -V68- (meas block val 2.3)
28 Position footwell/defrost Value Learned Central air flap motor -V70- (meas block val 3.4)
29 Actual value Sensor Central air flap motor -V70- (meas block val 3.1)
30 Position instrument panel vents Value Learned Central air flap motor -V70- (meas block val 3.3)
31 Position resirc air passenger compartment Value Learned Air flow flap motor -V71- (meas block val 5.4)
32 Actual value Sensor Air flow flap motor -V71- (meas block val 5.1)
33 Stop position fresh air passenger compartment Value Learned Air flow flap motor -V71- (meas block val 5.3)
34 Position defroster Value Learned Footwell/defroster Flap Motor -V85- (meas block val 4.4)
35 Actual value Sensor Footwell/defroster Flap Motor -V85- (meas block val 4.1)
36 Position footwell Value Learned Footwell/defroster Flap Motor -V85- (meas block val 4.3)
37 Sensor
38 Sensor
39 Sensor
40 Sensor

I have also created an Excel version, if you are interested:
http://home.online.no/~b-bado/car/Climatronic.xls" onclick="window.open(this.href);return false;

[youtube]<object width="425" height="344"><param name="movie" value="http://www.youtube.com/v/gKSK7YkVt3A&hl ... ram><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/gKSK7YkVt3A&hl=en&fs=1" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="425" height="344"></embed></object>[/youtube]


[youtube]<object width="425" height="344"><param name="movie" value="http://www.youtube.com/v/j8bmnpdjSK0&hl ... ram><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/j8bmnpdjSK0&hl=en&fs=1" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="425" height="344"></embed></object>[/youtube]

[Ghidora]

Fedt nok!

"The speedometer has a factory built-in error to show a speed faster than your actual speed."

Det kan da ikke være meget?

[ThomasMN]

På 195/65-15 kører jeg iflg. både GPS og klimaanlægget 97 km/t når speedometeret står på 100 km/t

[ThomasMN]

Til nyere Climatronic som dem her.





1. Hold down "ECON", and press the "up-vent" button (next to recirculation). Both temperature displays will read 00 or 00'0, and you can release the buttons once they do.
2. Twist the LEFT temperature knob until the display above reads 19’0.
3. Twist the FAN knob until the left temperature display reads 19’1 (like 19.1).
4. The right temperature display is now a digital speedometer! HOW COOL IS THAT!!!

--- For tach (in x100), twist the FAN knob until the left temperature display reads 19’3 (like 19.3)

--- To reset and go back to normal operation, hit the ECON button once.

These are the different settings the Climatronic can display. The numbers on the left indicate the “CHANNEL” it MUST be SET to:

• 1.0: Temp as read by sensor in middle fan speed knob.
• 1.4: Light intensity falling on same sensor.
• 4.0: Outside Temp – front bumper
• 4.1: Outside Temp – roof.
• 4.2: Outside Temp – rear bumper (inside temp?)
• 15.0: Oil Temp
• 19.0: Uncorrected Speed (Km/h)
• 19.1: Uncorrected Speed (Mp/h)
• 19.2: Coolant Temp
• 19.3: Tachometer (x100rpm)
• 19.4: Oil Pressure
• 25.0: Voltage

[tisbris]

audi tt - type 8n

koder:
http://www.wak-tt.com/tt/climatecontcodes.htm

Video:
http://www.youtube.com/watch?v=gU6aiySTHpU

[Jabbe]

Der er ikke nogen der har noget til en Seat Leon årgang 00-2005 ?

[zali]

Værsgo Leon 2000-2005

1 System fejl - vises som en diagnostisk Trouble Code (DTC),
2 Digital værdien af Interiør Temperatur Sensor, i Headliner (G 86)
3 Digital værdien af Interiør Temperatur Sensor, i Instrument Panel (G 56)
4 Digital værdien af frisk luft Duct Temperatur Sensor (G 89)
5 Digital værdien af fri luft (omgivende) temperatur Sensor (G 17), foran
6 Digital værdien af fri luft (omgivende) temperatur sensor
7 Digital værdien af Omgivende temperatur sensor På Fresh Air Blæser (G 109)
8 Digital værdien af Temperatur Regulator Flap Motor Potentiometer (G 92)
9 Delta værdien af Temperatur Regulator Flap
10 Ikke-korrigeret bestemt værdi af Temperatur Regulator Flap
11 Digital værdien af Central Flap Motor Potentiometer (G 112)
12 Specificeret værdi af Central Flap
13 Digital værdien af Footwell / defroster Flap Motor Potentiometer (G 114)
14 Specificeret værdi af Footwell / defroster Flap
15 Digital værdien af Air Flow Flap Motor Potentiometer (G 113)
16 Specificeret værdi af Air Flow Flap
17 Vehicle Hastighed (km / t)
18 Faktisk Air Blæser spænding (volt)
19 Specificeret Fresh Air Blæser spænding (volt)
20 A / C kompressor (A / C Kobling) spænding (volt)
21 Antal lav spænding hændelser, ikke-forbigående
22 Cycle betingelse af A / C Kølemiddel High Pressure Switch (F 118)
23 Cyclings af A / C Kølemiddel High Pressure Switch (F 118)
24 Cyclings af switches, absolut ikke-svingende
25 Analog / Digital værdi, Kick-Down Switch
26 Analog / Digital værdi, Kølevæsketemperatur (ECT) Advarsel Light
27 Kodning værdi
28 Motor Speed (RPM)
29 A / C kompressor hastighed i rpm (Lig Engine Speed x 1,28)
30 Software version
31 Display check (alle segmenter af A / C Control Head display lyser)
32 Potentiometer funktionsfejl Tæller Temperatur Regulator Flap
33 Potentiometer funktionsfejl counter, Central Flap
34 Potentiometer funktionsfejl Tæller Footwell / defroster Flap
35 Potentiometer funktionsfejl counter, Air Flow Map
36 Feedback værdi, kolde ende-stop, temperatur regulator Flap Motor Potentiometer (G 92)
37 Feedback værdi, varme ende-stop, temperatur regulator Flap Motor Potentiometer (G 92), max. stop
38 Feedback værdi, kolde ende-stop, Central Flap Motor Potentiometer (G 112)
39 Feedback værdi, varme ende-stop, Central Flap Motor Potentiometer (G 112)
40 Feedback værdi, kolde ende-stop, Footwell / defroster Flap Motor Potentiometer (G114)
41 Feedback værdi, varme ende-stop, Footwell / defroster Flap Motor Potentiometer (G114)
42 Feedback værdi, kolde ende-stop, Air Flow Map Motor Potentiometer (G 113)
43 Feedback værdi, varme ende-stop, Air Flow Map Motor Potentiometer (G 113)
44 køretøjer operation cyklus counter
45 Beregnet indvendige temperatur (intern software, med tal)
46 Udenfor (omgivende) temperatur, filtreret, for regulering (interne software)
47 Udenfor (omgivende) temperatur, ufiltreret, (interne software, i grader C)
48 Udenfor (omgivende) temperatur, ufiltreret, (i tal)
49 Fejlfunktion tæller for speedometer (hastighed) signal
50 stående tid (i minutter)
51 Kølevæsketemperatur (ECT) i grader C
52 Grafik kanal 1 - A / C kompressor switch-off forhold er identificeret ved belyste dele af "88,8" skærm. Se nedenstående figur.

53 Grafik kanal 2 - Klima system elektrisk output er identificeret ved belyste dele af "88,8" skærm. Se nedenstående figur.

54 Kontrol egenskaber
55 Udenfor (omgivende) temperatur i grader C eller grader F, afhængigt af indstillingen på A / C kontrol hovedet
56 Temperatur i grader C, fra indenrigs Temperatur Sensor, i Headliner (G 86)
57 Temperatur i grader C, fra indenrigs Temperatur Sensor, i Instrument Panel (G 56)
58 Temperatur i grader C, fra frisk luft Duct Temperatur Sensor (G 89)
59 Temperatur i grader C, fra udeluft (Ambient) Temperatur Sensor (G 17), foran
60 Temperatur i grader C, fra den omgivende temperatur sensor På Fresh Air Blæser (G 109)
61 Software version (senest)

Dette er oversat fra googletranslate til dansk.
Håber du kan bruge dette

[nogge]

Zali -> Har du ikke en til en golf 4 gti fra 98 os ?

[koden]

ved det er et gammelt indlæg...
finde ud af hvorfor min blæser ikke virker i øjeblikket men dog går i gang ind imellem.

holder taster inde og får nogle fejl i display:

til venstre skifter den mellem fejl 15 og 17 og til højre står der 04


kan ujeg bruge det til noget i mit blæser fejl søgning?

[Abdullah]

ved det er et gammelt indlæg...
finde ud af hvorfor min blæser ikke virker i øjeblikket men dog går i gang ind imellem.

holder taster inde og får nogle fejl i display:

til venstre skifter den mellem fejl 15 og 17 og til højre står der 04


kan ujeg bruge det til noget i mit blæser fejl søgning?

Ved godt at tråden er endnu ældre nu, men har en golf v, med præcis samme problem, fandt du nogensinde en løsning?

[koden]

hej.

jeg købte en brugt blæser på EBAY og skiftede den ud hvilket er pærelet.

alt virker nu

[Abdullah]

Mange tak

[Uffe]

Flere koder til det nyere klimatronic:


0 – 0 Program number Digital
0 – 1 ERL Left Digital
0 – 2 ERL Right Digital
0 – 3 Point being used Digital
0 – 4 Re-circulating Automatic Digital
0 – 5 Stationary Heating Active Digital
0 – 6 Air Quality (7 = Fresh Air) Digital
0 – 7 Derived Digital
0 – 8 Country Acronym Digital
0 – 9 Sensor Zone Head °C

1. UIF
1 – 0 Internal Temperature °C
1 – 1 External Temperature °C
1 – 2 Temperatura? Piastrine? In? Platino? °C
1 – 3 Correttore? Piastrine? In? Platino? °C
1 – 4 Uif-Sonnenint? Digital
1 – 5 Sun Intensity Corrected °C
1 – 6 Correttore? Dinamico? °C
1 – 7 Correttore? ricircolo? °C
1 – 8 correttore? termico? °C
1 – 9 Compensazione accensione UIF? °C

2. Sun Intensity Sensor Left
2 – 0 Sun Intensity Not Corrected W/m2
2 – 1 Sun Intensity Corrected W/m2
2 – 2 Fan Correction W/m2
2 – 3 Value Digital

3. Sun Intensity Sensor Right
3 – 0 Sun Intensity Not Corrected W/m2
3 – 1 Sun Intensity Corrected W/m2
3 – 2 Fan Correction W/m2
3 – 3 Value Digital

4. External Temperature
4 – 0 Temperature External °C
4 – 1 Temperature External CANBUS °C
4 – 2 Temperature Intake °C

5. Temperature Left Setpoint
5 – 0 Temperature Output °C
5 – 1 Difference between temp and temp setpoint °C
5 – 2 Regulator Setting (½%)
5 – 3 Pi-Stell-Max? (½%)
5 – 4 Defrost Digital

6. Temperature Left Actual
6 – 0 Temperature °C
6 – 1 Footwell °C
6 – 2 Vents °C

7. Temperature Right Setpoint
7 – 0 Temperature Output °C
7 – 1 Difference between temp and temp. setpoint °C
7 – 2 Regulator Setting (½%)
7 – 3 Pi-Stell-Max? (½%)
7 – 4 Defrost Digital

8. Temperature Right Actual
8 – 0 Temperature °C
8 – 1 Footwell °C
8 – 2 Vents °C

9. Evaporator Temperature Setpoint
9 – 0 Evaporator temperature °C
9 – 1 Difference between temp actual and temp Setpoint °C
9 – 2 Evaporator value settings 5mA/Dig
9 – 3 Sensor Sight

10. Evaporator Temperature Actual
10 – 0 Evaporator Temperature °C
10 – 1 Liquid refrigerant pressure bar
10 – 2 Liquid refrigerant temperature °C

11. AC Compressor
11 – 0 Power setpoint mA
11 – 1 Power actual mA
11 – 2 Power maximum mA
11 – 3 Compressor PWM Digital (0-200)
11 – 4 Power offset compressor
11 – 5 Power value Digital
11 – 6 Compressor code

12. Climate Control Fan
12 – 0 Fan Setpoint Voltage V
12 – 1 Manual regulation
12 – 2 Code anomaly
12 – 3 Reduction impeller V
12 – 4 Impeller offset 0.1V

13. Temperature Air Vent Left
13 – 0 Setpoint value %
13 – 1 Setpoint temperature Digital
13 – 2 Actual Temperature Digital
13 – 3 Maximum Temperature Digital
13 – 4 Minimum Temperature Digital

14. Temperature Air Vent Right
14 – 0 Setpoint value %
14 – 1 Setpoint temperature Digital
14 – 2 Actual Temperature Digital
14 – 3 Maximum Temperature Digital
14 – 4 Minimum Temperature Digital

15. Temperature Air Vent Diffuser
15 – 0 Setpoint value %
15 – 1 Setpoint temperature Digital
15 – 2 Actual Temperature Digital
15 – 3 Maximum Temperature Digital
15 – 4 Minimum Temperature Digital

16. Temperature Air Vent Defrost
16 – 0 Setpoint Value %
16 – 1 Setpoint temperature Digital
16 – 2 Actual Temperature Digital
16 – 3 Maximum Temperature Digital
16 – 4 Minimum Temperature Digital

17. Temperature Internal Recirculation
17 – 0 Setpoint Value %
17 – 1 Setpoint temperature Digital
17 – 2 Actual Temperature Digital
17 – 3 Maximum Temperature Digital
17 – 4 Minimum Temperature Digital

18. Temperature External Air
18 – 1 Setpoint Temperature Digital
18 – 2 Actual Temperature Digital
18 – 3 Maximum Temperature Digital
18 – 4 Minimum Temperature Digital

19. Engine Data
19 – 0 Vehicle Speed (kph) kph
19 – 1 Vehicle Speed (mph) mph
19 – 2 Engine Temperature °C
19 – 3 Engine speed RPM
19 – 4 AC compress speed RPM

20. CanBus Data
20 – 0 Additional Heating 1=on
20 – 1 PTC Confirmation 1=on
20 – 2 Effective Power PTC A
20 – 3 Air requested from external %
20 – 4 External air percentage cooler %
20 – 5 Performance heating 1=no external provision

21. Air Distribution
21 – 0 Defrost %
21 – 1 Face %
21 – 2 Feet %
21 – 3 Air Vent Diffuser %
21 – 4 Re-circulated %
21 – 5 Air Sensor %

22. Time
22 – 0 Engine Off Time minutes
22 – 1 Engine Operating Time seconds
22 – 2 Operating Time with Ignition On seconds
22 – 3 ?
22 – 4 ?
22 – 5 ?

23. Special Channel
23 – 0 Inner Lighting Sensor Digital
23 – 1 Air Quality Sensor

24. Software Version
24 – 0 Development State
24 – 1 Software Version
24 – 2 Type of Software
24 – 3 Keep Frozen 0/1 – Diagnosis
24 – 4 Version K Matrix
24 – 5 EEP – Test flags
24 – 6 Encryption Vag (2)

25. Test Channels
25 – 0 Channel 0
25 – 1 Channel 1
25 – 2 Channel 2
25 – 3 Channel 3
25 – 4 Channel 4
25 – 5 Channel 5
25 – 6 Channel 6
25 – 7 Channel 7
25 – 8 Channel 8
25 – 9 Channel 9

26. Parameters for inventory on crystals
26 – 0 Delay seconds
26 – 1 Step/udm? (Digital) Digital
26 – 2 Minimal Limit (Digital) Digital
26 – 3 Maximum Limit (Digital) Digital
26 – 4 Step/udm? HellaKit? 1=connected

27. Direct Ventalation
27 – 0 Setpoint Value %
27 – 1 Setpoint temperature Digital
27 – 2 Actual Temperature Digital
27 – 3 Maximum Temperature Digital
27 – 4 Minimum Temperature Digital

28. Humidity
28 – 0 Setpoint Humidity %
28 – 1 Relative Humidity %
28 – 2 Temperature Crystal WSS °C
28 – 3 Dewpoint temperature °C
28 – 4 Melting point °C

29. Raw Humidity
29 – 0 Temperature crystals corrected °C
29 – 1 Temperature crystals uncorrected °C
29 – 2 Humidity Sensor %
29 – 3 Temperature sensor °C
29 – 4 Dew point temperature (measurement test) °C
29 – 5 Code anomaly


30. Humidity Values
30 – 0 Thermophilic sensor value Digital
30 – 1 Thermophilic sensor reference Digital
30 – 2 Moisture duration 10 to the power of -4 sec
30 – 3 Humidity reference temperature Digital
30 – 4 Humidity sensor %
30 – 5 Temperature sensor °C
30 – 6 Temperature sensor (uncorrected) °C

[muffed]

Super fedt, men støder på en fejl i mit climatronic som ikke vcds finder.

har en leon 1m som Zali har lagt link op til, i channel 1 kommer der en (DTC) fejl kode 5.3 som skulle være "outside air (ambient) temperature sensor, front, sporadic open"

går ud fra det er G17 føleren som sidder i kofangeren, den er skiftet, men fejlen forsvinder ikke i panelet, ej heller ved afbrudt batteri.
umiddelbar ligger temperaturen i kanal 4,5 og 6 nogenlunde ens. syntes at kan kommet frem til at kanal 6 er en middelværdi af G89 og G17

nogen bud på hvad det så er for en føler